3 4 6 7 8 9 0 3 4 5 6 7 8 9 0 3 5 O A B C D P E F Q R H G I J K L M N 4 English 8 4 Cestina 4 eesti 58 Hrvatski 73 Magyar 89 05 Lietuviskai 3 Latviesu 39 PoLski 54 roMân 70 87 sLovensky 05 sLovensCina srPski 36 5 RQ1095, RQ1085, RQ1075 6 English introduction Thank you for buying this Philips shaver. Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable. important Read this user manual carefully before you use the shaver, the Jet Clean System and the Power Pod. Save the user manual for future reference. Danger Make sure the adapter does not get wet (Fig. 1). Warning Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation. These appliances are not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliances. Caution Do not use the shaver, the Jet Clean System, the Power Pod or the adapter if it is damaged. Charge and store the shaver at a temperature between 5°C and 35°C. Always put the protection cap on the shaver to protect the shaving heads when you are travelling. Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. Only use the adapter supplied. If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. - - English - 7 Only use the Jet Clean System with the original HQ200 cleaning fluid. Never immerse the Jet Clean System in water nor rinse it under the tap. (Fig. 2) Use and store the Jet Clean System at a temperature between 5°C and 35°C. Always place the Jet Clean System on a stable, level and horizontal surface to prevent leakage. Empty the cleaning chamber and clean it thoroughly by rinsing it with hot tap water every 15 days. Always place the Jet Clean System on a fluid-resistant surface. The Jet Clean System thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others. The cleaning chamber of the Jet Clean System is not dishwasherproof. When the Jet Clean System is ready for use, do not move it to prevent leakage of cleaning fluid. Never immerse the Power Pod in water, nor rinse it under the tap (Fig. 3). Compliance with standards The shaver complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap (Fig. 4). These Philips appliances comply with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliances are safe to use based on scientific evidence available today. general The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts. Noiselevel: Lc= 64 dB(A) Overview (Fig. 5) - - A B C D Protection cap Shaving unit Trimmer Trimmer on/off slide 8 English Shaver (RQ1090/RQ1060/RQ1050) Shaver on/off button Display Shaver holder Jet Clean System (RQ1005/RQ1000) Jet Clean System on/off button Cleaning symbol Drying symbol 'Cleaning chamber empty' symbol Cleaning chamber Power Pod Cleaning brush Adapter Small plug the display E F G H I J K L M N O P Q R Before you use the shaver for the first time, remove the protective foil from the display. The three shaver types (RQ1090, RQ1060 and RQ1050) have different displays, which are shown in the figures below. - RQ1090 (Fig. 6) - RQ1060 (Fig. 7) - RQ1050 (Fig. 8) Charging Charging takes approx. 1 hour. When you place the shaver in the Jet Clean System or in the Power Pod, the display automatically switches off after approx. 5 hours. RQ1090 When the shaver is charging, the minutes indication and the plug symbol flash (Fig. 9). The shaving minutes increase until the shaver is fully charged. RQ1060 When the shaver is charging, the plug symbol flashes. (Fig. 10) - English First the arrowheads of the bottom charge level flash, then the arrowheads of the second level flash, and so on until the shaver is fully charged. RQ1050 When the shaver is charging, the battery symbol flashes blue. (Fig. 11) Battery fully charged - 9 - RQ1090 When the battery is fully charged, the minutes indication is visible on the display and the plug symbol disappears from the display. (Fig. 12) RQ1060 When the battery is fully charged, all arrowheads and all charge level lights light up blue continuously and the plug symbol disappears from the display (Fig. 13). When you remove the shaver from the Jet Clean System or the Power Pod, the arrowheads of the top charge level light up blue to indicate that the battery is full (Fig. 14). RQ1050 When the battery is fully charged, the battery symbol lights up blue c ontinuously. (Fig. 15) Battery low RQ1090 When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the minutes indication and the plug symbol start to flash (Fig. 9). When you switch off the shaver, the shaving minutes and the plug symbol continue to flash for a few more seconds. You hear a beep when there are no minutes left. RQ1060 When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the battery symbol flashes red and the arrowheads of the bottom charge level flash blue. (Fig. 16) - - - - 0 - English When you switch off the shaver, the battery symbol and the arrowheads of the bottom charge level continue to flash for a few seconds. RQ1050 When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the battery symbol lights up red. (Fig. 11) When you switch off the shaver, the battery symbol starts to flash for a few seconds. remaining battery capacity RQ1090 The remaining battery capacity is indicated by the number of shaving minutes shown on the display. (Fig. 12) RQ1060 The remaining battery capacity is indicated by the flashing arrowheads of a particular charge level (Fig. 14) Clean shaver - - - For optimal shaving performance, we advise you to clean the shaver after every use. - The tap symbol flashes to remind you to clean the shaver (Fig. 17). Note:The displays of types RQ1060 and RQ1050 look different but show the same indication. Replace shaving unit For maximum shaving performance, we advise you to replace the shaving unit every two years. - To remind you to replace the shaving unit, the shaving unit symbol flashes (all types) and you hear a beep when you switch off the shaver (RQ1090 only). This happens at the end of 7 successive shaves to remind you to replace the shaving unit. (Fig. 18) Note:The displays of types RQ1060 and RQ1050 look different but show the same indication. English travel lock You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident. activating the travel lock Press the on/off button for 3 seconds to enter the travel lock mode (Fig. 9). , The lock symbol appears on the display (all types) and you hear a beep (RQ090 only) to indicate that the travel lock has been activated. Note:The displays of types RQ1060 and RQ1050 look different but show the same indication. Deactivating the travel lock Press the on/off button for 3 seconds. , The motor starts running to indicate that the travel lock has been deactivated. The shaver is now ready for use again. Note:When you place the shaver in the plugged-in Power Pod or Jet Clean System, the travel lock is automatically deactivated. Blocked shaving heads If the shaving heads are blocked, the shaving unit symbol and the tap symbol with exclamation mark flash. In this case, the motor cannot run because the shaving heads are soiled or damaged. (Fig. 20) Note:The displays of types RQ1060 and RQ1050 look different show the same indication. - When this happens, you have to clean the shaving unit or replace it. - The shaving unit symbol and the tap symbol with exclamation mark continue to flash until you unblock the shaving heads. English Charging Charging takes approx. 1 hour. A fully charged shaver has a shaving time of up to 65 minutes, which is enough for approx. 21 shaves. The actual shaving time is calculated by the shaver. If you have a heavy beard, the shaving time may be less than 65 minutes. The shaving time may also vary over time, depending on your shaving behaviour and beard type. Quick charge After the shaver has charged for 5 minutes, it contains enough energy for one shave. Charging in the Power Pod Put the small plug in the Power Pod (Fig. ). Put the adapter in the wall socket. 3 Pull at the top of the lid () and remove it () (Fig. ). 4 First insert the top of the shaver into the Power Pod () and then press the bottom part into the Power Pod () (Fig. 3). Note:The shaver cannot be placed in the Power Pod when the protection cap is on the shaving unit. , The display shows that the shaver is charging (see chapter `The display'). Charging in the Jet Clean system Put the small plug in the Jet Clean System. Put the adapter in the wall socket. 3 Place the shaver upside down in the holder with the display pointing towards the front of the Jet Clean System (Fig. 4). Note: RQ1090,RQ1060 only: when you turn the shaver upside down, the indications on the display are also turned upside down so you can still see the remaining battery capacity. English 3 4 Press the shaver tightly into the holder to lock it into place (Fig. 5). Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit. , The display shows that the shaver is charging (see chapter `The display'). using the shaver shaving Press the on/off button once to switch on the shaver. , The display lights up for a few seconds. Move the shaving heads over your skin. Make both straight and circular movements (Fig. 6). - Shaving on a dry face gives the best results. - Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 3 Press the on/off button once to switch off the shaver. , The display lights up for a few seconds and then shows the remaining battery capacity (RQ090/RQ060 only). trimming You can use the trimmer to groom your sideburns and moustache. Pull the shaving unit off the shaver (Fig. 7). Press the on/off button once to switch on the shaver. , The display lights up for a few seconds. 4 You can now start trimming. 5 Press the trimmer slide backwards to retract the trimmer. 6 Press the on/off button once to switch off the shaver. , The display lights up for a few seconds and then shows the remaining battery capacity (RQ090/RQ060 only). 3 Press the trimmer slide forwards to slide out the trimmer (Fig. 8). 4 English 7 Insert the lug of the shaving unit into the slot in the top of the shaver (). Then press the shaving unit downwards () to attach it to the shaver (`click') (Fig. 9). Cleaning and maintenance Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. The best and most hygienic way to clean the shaver is in the Jet Clean System. You can also rinse the shaver under the tap or clean it with the brush supplied. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Clean the shaver after every shave for optimal shaving performance. You can clean the outside of the shaver with a damp cloth. Regular cleaning guarantees better shaving performance. Cleaning the shaving unit in the Jet Clean system The Jet Clean System has three cleaning programs: the eco program, the normal program and the intensive program. The shaver automatically chooses the appropriate cleaning program. Preparing the Jet Clean system for use Fill the cleaning chamber before first use. Put the small plug in the Jet Clean System. Put the adapter in the wall socket. , The holder automatically moves to the highest position. 3 Simultaneously press the release buttons on both sides of the cleaning chamber (). Then lift the Jet Clean System off the cleaning chamber (). (Fig. 30) , The cleaning chamber remains behind. 4 Unscrewthecapfromthebottlewithcleaningfluidandremove the airtight seal. English 5 5 FillthecleaningchamberwithHQ200cleaningfluiduptotheMAX indication (Fig. 3). 6 Place the Jet Clean System back onto the cleaning chamber (Fig. 3). Make sure the release buttons click back into place. using the Jet Clean system Place the shaver in the holder. , The display shows that the shaver is charging (see chapter `The display') (Fig. 33). Press the on/off button on the Jet Clean System to start the cleanin ...