SCD520 1 EngliSh 6 0 Cestina 6 eesti 50 Hrvatski 6 Magyar 77 91 Lietuviskai 107 Latviesu 1 PoLski 15 roMân 19 16 sLovensky 179 sLovensCina 19 srPski 06 0 SCD520 6 EngliSh introduction Congratulations on your purchase and welcome to Philips AVENT! To fully benefit from the support that Philips AVENT offers, register your product at www.philips.com/welcome. Philips AVENT is dedicated to producing caring, reliable products that give parents the reassurance they need. This Philips AVENT baby monitor provides round-the-clock support by ensuring you can always hear your baby clearly without any distracting noise. The DECT technology guarantees zero interference from other wireless appliances and a crystal clear signal between the baby unit and the parent unit. The temperature sensor enables you to monitor the temperature in your baby's room, and offers you personalised settings to help keep your baby's room comfortable. general description (Fig. 1) a 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Parent unit On/off button 3 Slot for belt clip TALK button MENU button LINK light Microphone Loudspeaker Menu and volume +/­ buttons OK button Display Sound level lights Belt clip Adapter Small appliance plug Charger Charging light Compartment for rechargeable batteries Neck strap Lid of compartment for rechargeable batteries Rechargeable batteries (included) Opening for neck strap Baby unit On/off button 3 PAGE button Play/stop button E Lullaby button K Battery light T Nightlight button Q Power-on light Volume +/­ buttons Microphone Adapter Large appliance plug Loudspeaker Temperature sensor Socket for large appliance plug Compartment for non-rechargeable batteries Lid of compartment for non-rechargeable batteries Non-rechargeable batteries (not included) EngliSh 7 C Display 1 Ñ° = room temperature indication 2 R= sound alert 3 K = lullaby 4 Q = nightlight 5 T = battery symbol For other display indications and volume/sensitivity levels, see chapters `Features' and `Menu options'. important Read this user manual carefully before you use the appliance and save it for future reference. Danger Never immerse any part of the baby monitor in water or any other liquid. Warning Check if the voltage indicated on the adapters of the baby unit and the charger corresponds to the local mains voltage before you connect the appliance. Only use the adapter supplied to connect the baby unit to the mains. Only use the charger and adapter supplied to charge the parent unit. The adapters contain a transformer. Do not cut off the adapters to replace them with other plugs, as this causes a hazardous situation. If the adapters are damaged, always have them replaced with one of the original type in order to avoid a hazard. For the correct type, see chapter `Replacement'. If the charger of the parent unit is damaged, always have it replaced with one of the original type. Never use the baby monitor in moist places or close to water. Except for the battery compartments, do not open the housing of the baby unit and parent unit in order to prevent electric shock. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Caution Use and store the appliance at a temperature between 10°C and 40°C. Do not expose the baby unit and parent unit to extreme cold or heat or to direct sunlight. Do not put the baby unit and the parent unit close to a heating source. Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/3 feet away). Never place the baby unit inside the baby's bed or playpen. Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket). Always place non-recheargeable batteries of the correct type in the baby unit. Always place rechargeable batteries of the correct type in the parent unit. If you place the parent unit next to a transmitter or other DECT appliance (e.g. a DECT telephone), the connection with the baby unit may be lost. general This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. The temperature sensor only measures the temperature in the baby room. It cannot be used to control or adjust the temperature in the baby room. - - 8 EngliSh electromagnetic fields (eMF) This Philips AVENT appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Preparing for use Baby unit You can use the baby unit from the mains or on non-rechargeable batteries. Even if you are going to use the unit from the mains, we advise you to insert the non-rechargeable batteries. This guarantees automatic back-up in case of mains failure. Mains operation 1 Put the large appliance plug in the baby unit and put the adapter in a wall socket (Fig. ). , The power-on light goes on. Operation on non-rechargeable batteries The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use Philips LR6 PowerLife batteries. Do not use rechargeable batteries, as the baby unit does not have a charging function. Unplug the baby unit and make sure your hands and the unit are dry when you insert the nonrechargeable batteries. 1 Remove the lid of the compartment for non-rechargeable batteries. (Fig. ) Insert four non-rechargeable batteries (Fig. ). Note: Make sure the + and - poles point in the right direction. Reattach the lid. (Fig. 5) Note:When the batteries are low, the battery light on the baby unit flashes red. Parent unit Operation on rechargeable batteries The parent unit comes with two rechargeable NiMH AAA 900mAh batteries. Charge the parent unit before you use it for the first time or when the parent unit indicates that the batteries are low (the empty battery symbol flashes on the display and the parent unit beeps). The parent unit starts indicating that the batteries are low 30 minutes before the batteries are completely empty. Note: If the batteries are completely empty, the parent unit automatically switches off and loses contact with the baby unit. 1 Remove the lid of the compartment for the rechargeable batteries (Fig. 6). Insert the rechargeable batteries (Fig. 7). Note: Make sure the + and - poles of the batteries point in the right direction. Reattach the lid (Fig. 8). Insert the small appliance plug into the charger, put the adapter in a wall socket and place the parent unit in the charger (Fig. 9). , The charging light on the charger goes on. , The display shows a charging battery symbol to indicate that the parent unit is charging. 5 Leave the parent unit in the charger until the batteries are fully charged. , During charging, the charging light on the charger lights up continuously. EngliSh , When the batteries are fully charged, the display of the parent unit shows a full battery symbol T. When you charge the parent unit for the first time or after a long period of disuse, switch it off and let it charge continuously for at least 10 hours. Charging normally takes 8 hours, but it takes longer when the parent unit is switched on while charging. To keep the charging time as short as possible, switch off the parent unit during charging. When the batteries are fully charged, the parent unit can be used cordlessly for at least 24 hours. 9 Note:When the parent unit is charged for the first time, the operating time is less than 24 hours.The batteries only reach their full capacity after you have charged and discharged them four times. Note:When the parent unit is not in the charger, the batteries gradually discharge, even when the parent unit is switched off. using the appliance 1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 10). Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. Press and hold the on/off button 3 on the baby unit until the green power-on light goes on. (Fig. 11) Note:The power-on light always lights up green, even when there is no connection with the parent unit. , The nightlight lights up briefly and then goes out again. , The battery light T lights up briefly and then goes out again. (Fig. 12) Press and hold the on/off button 3 on the parent unit until the sound level lights light up briefly. (Fig. 13) , The display goes on and the battery symbol appears on the display (Fig. 1). , The LINK light flashes red and the message `Searching' appears on the display. (Fig. 15) , The LINK light on the parent unit turns green and lights up continuously when a connection has been established between the baby unit and parent unit. The message `Linked' appears on the display. (Fig. 16) , After 2 seconds the message `Linked' disappears and the temperature value is shown on the display. (Fig. 17) , If no connection is established, the LINK light on the parent unit stops flashing and lights up red. The parent unit beeps from time to time and the message `Not Linked' appears on the display. (Fig. 18) Positioning the baby monitor 1 Place the baby unit at least 1 metre/ feet away from your baby (Fig. 19). Place the parent unit within the operating range of the baby unit. Make sure it is at least 1 metre/ feet away from the baby unit to avoid acoustic feedback (Fig. 0). For more information on the operating range, see section `Operating range' below. Operating range The operating range of the baby monitor is 330 metres/1000 feet in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is up to 50 metres/150 feet. Dry materials Wood, plaster, cardboard, glass (without metal, wires or lead) Material thickness < 30cm/12in Loss of range 0-10% 10 EngliSh Material thickness < 30cm/12in < 30cm/12in < 1cm /0.4in < 1cm/0.4in Loss of range 5-35% 30-100% 90-100% 100% Dry materials Brick, plywood Reinforced concrete Metal grilles or bars Metal or aluminium sheets For wet and moist materials, the range loss may be up to 100%. Features The following features are described in chapter `Menu options', as they can only be operated in the menu of the parent unit: - Adjusting microphone sensitivity - Sound alert on/off - Setting room temperature range (minimum and maximum temperature) - Temperature alert on/off adjusting loudspeaker volume 1 Press the volume + or ­ button on the baby unit until the desired loudspeaker volume for the baby unit has been reached (Fig. 1). Note:You can only set the loudspeaker volume on the baby unit when a lullaby is playing. Press the volume + or ­ button on the parent unit until the desired loudspeaker volume for the parent unit has been reached (Fig. ). , The display gives visual feedback on the volume settings of the parent unit: - j = volume switched off/silent baby monitoring - k = minimum volume - l = maximum volume Note: If the volume is set to a high level, the units consume more power. talk function You can use the TALK button on the parent unit to talk to your baby (e.g. to comfort your baby). 1 Press and hold the TALK button and talk clearly into the microphone from a distance of 150cm (Fig. ). , The green LINK light starts flashing and the message `Talk' appears on the display. Release the TALK button when you have finished talking. sound level lights The parent unit continuously monitors the sound level in your baby´s room and the sound level lights let you know if there is any activity. If your baby cries, you see the sound level lights light up on the parent unit. - As long as the baby unit does not detect a sound, all sound level lights on the parent unit are out. - When the baby unit picks up a sound, one or more sound level lights on the parent unit go on. The number of lights that go on is related to the loudness of the sound picked up by the baby unit. EngliSh 11 nightlight Note:You can also switch the nightlight on and off in the menu of the parent unit (see chapter `Menu options', section `Nightlight'). 1 Press the nightlight button Q on the baby unit to switch on the nightlight. (Fig. ) , Q appears on the display of the parent unit. Tip: Switch off the nightlight when you operate the baby unit on the non-rechargeable batteries.This saves power. Paging the parent unit If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button on the baby unit to locate the parent unit. Note:The paging function only works when the parent unit is switched on. 1 Press the PAGE button on the baby unit (Fig. 5). , The message `Paging' appears on the display of the paren ...